Blob targets - The HuntingPA.com Outdoor Community
 
LinkBack Thread Tools
post #1 of 5 (permalink) Old 10-29-2016, 04:18 AM Thread Starter
Moderator
 
Join Date: Nov 2002
Location: PA
Posts: 12,747
Back To Top
Blob targets

I read a post on here about targets...I had a Rinehart 18-1...I believe it was 2013 when I bought it...it took 4 seasons of thousands of shots...with field points I'm pretty confident to say you couldn't ruin it..I shoot a lot of big fixed 4 blade broadheads..I've been through 2 bows...lots of tuning..I broadhead tune to atleast 40yds..I shoot atleast a few broadheads daily just to make sure everything is still true... overkill...but if I miss or make a bad shot I wanna know it was ME not my equipment..


Anyways..I finally got it to the point where I'm running out of foam. It'll still stop 95% of my shots without a passthrough but getting to tear up my hand crests and fletchings..

On the recommendation I bought a Blob target..

I went with their smaller model..it's only 6" thick..but weighs 30-35lbs..the bigger version would be nice..but right now I need portable..

I was skeptical...I really was...6" isn't much to stop an arrow... especially my arrows I built to achieve maximum penetration..


I got my blob last night...

When I saw the maker threw in a free arrow removal tool I was concerned...I DO NOT like a target that is a bear to pull arrows from.


I shot 20 or so arrows into it today..both fixed heads and field points..


The foam is extremely dense...but yet it's not rock hard..it's very interesting..


I was pleasantly surprised by the lack of penetration!


I didn't measure it...but my arrows weren't breaking through the back...so..less than 6"!


I can't speak for the longevity of it...I'd say it'll compare to the 18-1. Foam seems to be somewhat "self healing".


When it comes to pulling arrows..because of its size and shape, I tipped it over and stood on it and the arrows come right out...pulling isn't hard.. broadheads actually pull out cleanly and don't rip extra foam out because it is dense closed cell foam..



One thing I noticed...my broadhead shaft has very distinct lines in the spaces between each blade..my arrows are Victory VAPS with an "ice coating". I didn't examine it to see if it's simply a little bit of "melted" foam or if it's actually abrasive and wearing the coating or carbon off or what..they say it's not abrasive..I'm guessing it may be a foam build up...the field point shaft feels fine..but I shoot a point with a flared tip so it expands foam and pulls easier than a normal field point..



So far, I'm happy. If it holds up well and isn't trashing my shafts I will be extremely happy...if it is trashing my shafts I will contact the company...



Thought I'd share... definitely seems like a nice target worth checking out...


I would NOT shoot a mechanical into it...I'd imagine you'd be risking blade damage upon removal..but, my fixed blades do pull out the same exact path so maybe mechanical heads would too??
mauser06 is offline  
Sponsored Links
Advertisement
 
post #2 of 5 (permalink) Old 10-29-2016, 11:47 AM
Part of the Community
 
Join Date: Dec 2001
Location: Norry
Posts: 170
Back To Top
Re: Blob targets

I bought the large size several years ago for broadheds. It was so heavy I had to slide it on my cart to move it. I needed one I could put in my truck to take to a safe place to shoot broadheads. So I sawed it in half with a hand saw. I have been shooting broadheads into it for about 6 years and it is holding up. I think I can still get about 1 or 2 years out of it. Then I can start shooting at the other half ! I shoot several hundred shots a year into it. But I only shoot about 52 pounds of draw weight. I did spray paint aiming dots on front and back each side is off center from the the other side. that helps it last longer.
wolfy is offline  
post #3 of 5 (permalink) Old 10-29-2016, 04:38 PM
Diehard Outdoorsman
 
Hittingguru's Avatar
 
Join Date: Mar 2003
Location: Tioga and Potter Counties
Posts: 2,972
Back To Top
Re: Blob targets

I shot in an indoor dot league a few years ago where we had those. I was shooting X7 aluminum arrows- big 2613's. After shooting 450 rounds for 10 weeks, the blue of the shafts were worn away. One of the guys in the league is a machinist, and said that those targets will gradually "sand" away the arrow shaft. I personally didn't like them because with bigger arrows, you get an impact channel and the arrow would follow that, regardless if it was where you wanted it to go.

Wishing I was at camp!
Hittingguru is offline  
Sponsored Links
Advertisement
 
post #4 of 5 (permalink) Old 10-31-2016, 05:31 AM
Diehard Outdoorsman
 
muskyman62's Avatar
 
Join Date: May 2012
Location: Western PA
Posts: 2,575
Back To Top
Re: Blob targets

i was worried about what i thought was the arrow being worn away but after cleaning with alcohol i realized it was foam residue. if it is sanding away my arrows i could care less because my arrows would be retired before anything were to happen.

You want me to put my ear to the ground? Listen for hoof beats? Look for broken twigs?
muskyman62 is offline  
post #5 of 5 (permalink) Old 11-16-2016, 12:53 PM
Part of the Community
 
Join Date: Jun 2008
Location: PA
Posts: 238
Back To Top
Anyone sell (or make) these locally? The cost of shipping a big one is prohibitive for me.
Soularcher is offline  
Reply

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the The HuntingPA.com Outdoor Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page



Posting Rules  
You may not post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome